Genelec 1032B 10" 2-Way Bi-Amplified Active Monitor (Single) Black Veneer has been discontinued, here are some related products you might like:
Genelec 1032B 10" 2-Way Bi-Amplified Active Monitor (Single) Black Veneer
Features
- Intelligent Signal-Sensing Power Manager
- Auto-Start and Stand-By Mode
- Directivity Control Waveguide
- Bass-Reflex Enclosure
- Treble Tilt, Bass Tilt, Bass Roll-Off
Description
The Genelec 1032B 10" 2-Way Bi-Amplified Active Monitor (Single) Black Veneer is designed for high-power near-field monitoring such as in music studios, mobile vans, surround sound systems, multimedia installations, and TV broadcast facilities. The speaker consists of a 250 mm bass woofer, a 25 mm metal dome tweeter, a custom crossover network, and a removable rackmountable amplifier system on vibration isolators. The monitor utilises a directivity control waveguide to balance the frequency spectrum, and a long-flow bass-reflex enclosure to improve low-end performance.
The monitor uses a parallel bandpass filter crossover network set to 1,800 Hz with acoustically complementary 24 dB/octave slopes. It includes an input sensitivity adjustment control from -6 dBu to +7 dBu which provides a maximum SPL range of 100 dB at 1 m on the lowest setting to 113 dB at 1 m on the highest setting. The monitor also includes three advanced tone controls with treble tilt, bass tilt, and bass roll-off for tuning the performance of the system to different acoustic environments.
The 250 mmbass woofer is loaded into a 24-litre cabinet, is amplified by 180 W short-term power, and can play down to 36 Hz. You can supplement the bass by adding a Genelec 7071A subwoofer for even more low-frequency extension. The 25 mm metal dome tweeter can play up to 23,000 Hz, is amplified by 120 W short-term power, and utilises the directivity control waveguide to achieve phase and delay uniformity. Both the woofer and tweeter are magnetically shielded and utilise a thermal overload protection circuit. The monitor accepts a balanced signal via XLR connector and provides you with the controls to optimise the system performance for your listening position.
Features
Intelligent Signal-Sensing Power Manager
The monitor features a power-sensing circuit for automatically putting the unit into standby mode if an audio signal has not been detected for one hour. While in standby mode, the monitor consumes less than 0.5 W of power
Rackmountable Amplifier Section
The monitor includes the option of detaching the amplifier plate from the box for mounting within a 19" rack. This helps with cooling the amplifier and making adjustment controls more accessible
Bass-Reflex Enclosure
To improve low-frequency response, the backfiring wave of the woofer is sent through a ported long-flow bass-reflex enclosure
Directivity Control Waveguide
To achieve treble phase and delay alignment, the metal dome tweeter utilises the directivity control waveguide
Treble Tilt, Bass Tilt, Bass Roll Off
To adjust the monitor to different room acoustics, the amplifier includes treble tilt, bass tilt, and bass roll off controls.
Adjustable Input Sensitivity
To match the output of the monitor to your studio console, the amplifier includes an adjustable input sensitivity control between -6 to 7 dBu
Built-In Protection Circuit
To prevent thermal overload to the magnets in the woofer and tweeter, the amplifier includes a built-in overload protection circuit
Specifications
Low Cut Filters | Lower cut-off frequency: -3 db ≤40 Hz |
High Cut Filter | Upper cut-off frequency: -3 dB: ≥22,000 Hz |
Frequency Response | 42 to 21,000 Hz (±2.5 dB) |
SPL | Maximum short-term Sinae wave acoustic output on axis in half space, averaged from 100 to 3,000 Hz: At 1 m >113 dB SPL At 0.5 m >119 dB SPL Maximum long-term RMS acoustic output in same conditions with IEC-weighted noise (limited by driver unit protection circuit): At 1 m ≥103 dB SPL At 0.5 m ≥109 dB SPL Maximum peak acoustic output per pair above console bridge, at 1 m from the listening position with music material > 124 dB |
Self Noise | Self-generated noise level in free field at 1 metre on axis: <10 dB (A-weighted) |
Distortion | At 90 dB at 1 m on axis: 50 to 100 Hz: <1% >100 Hz: <0.5% |
Driver(s) | Bass: 250 mm cone Treble: 25 mm metal dome Both drivers are magnetically shielded |
Input Connector | XLR Female: pin 1 gnd, pin 2 +, pin 3 - |
Input Impedance | 10 kΩ balanced |
Input Level | For 100 dB SPL output at 1 m: variable from +6 to -6 dBu For maximum short-term Sinae wave output 113 db SPL at 1 m: variable from +19 to +7 dBU |
Filter | Subsonic filter below 40 Hz: 18 dB/octave Ultrasonic filter above 25,000 Hz: 12 dB/octave |
Crossover Frequency | Bass/Treble: 1,800 Hz Slopes: 24 to 32 dB/octave |
Tone Controls | Treble tilt control operating range in 2 dB steps: from +2 to -4 dB and MUTE Bass roll-off control operating range in 2 dB steps: from 0 to -8 dB at 40 Hz Bass tilt control operating range in 2 dB steps: from 0 to -8 dB at 80 Hz and MUTE |
Amplifier | |
Output Power | Bass amplifier short-term output power with a 4 Ω load: 180 W Treble amplifier short-term output power with an 8 Ω load: 120 W Long-term output power is limited by driver unit protection circuitry. |
Slew Rate | 80 V/μs |
Distortion | THD: ≤0.05% SMPTE-IM: ≤0.05% CCIF-IM: ≤0.05% DIM 100: ≤0.05% |
Signal to Noise Ratio | Referred to full output: Bass: >100 dB Treble: >100 dB |
Voltage | 230, 100/200 or 114/230V according to region |
Voltage Range | ±10% |
Power Consumption | Idle: 20 W Standby: <0.5 W Full Output: 200 W |
Dimensions (H x W x D) | 495 x 320 x 290 mm |
Weight | 21.7 kg |
In The Box
- Genelec 1032B 10" 2-Way Bi-Amplified Active Monitor (Single) Black Veneer
- Power Cord
Reviews
(no ratings yet)Give it a quick rating:
Thanks for your rating!
Write a review
Details
- Product: Genelec 1032B 10" 2-Way Bi-Amplified Active Monitor (Single) Black Veneer
- Manufacturer: Genelec
- Model: 1032BPM
- SKU: 1032BPM
- RM Product #: 29912