Sachtler aktiv8 flowtech75 MS Tripod System

Description

The aktiv8 flowtech75 MS Tripod System from Sachtler pairs the activ8 fluid head with the lightweight, carbon fibre flowtech 75 MS tripod with mid-level spreader. This kit offers lightning fast SpeedSwap technology, a sideload camera plate, 15 levels (+0) of counterbalance, 7 levels (+0) of pan and tilt drag, and stable support for camera rigs weighing up to 12 kg (26.5 lb). A padded carrying bag rounds out this tripod kit.

Sachtler aktiv8 Sideload Fluid Head with SpeedLevel & 7-Step Drag (75mm)

The aktiv8 Sideload Fluid Head uses Sachtler 's truly innovative SpeedLevel technology to provide almost instant mounting and levelling of your camera rig on your tripod. The clamp and stud SpeedLevel system saves precious time levelling your camera rig by eliminating the need to screw on a tie-down knob. Designed for documentary, news, and corporate productions, the aktiv8 supports rigs weighing up to 12 kg (26.5 pounds). This 75mm ball fluid head features 15 steps of counterbalance and seven steps of pan and tilt drag adjustment, plus zero settings for both balance and drag.

The SpeedLevel technology replaces the traditional head screw and tie-down design with a strong clamp built into the head bowl and a stud component that clamps onto your tripod bowl or other mounting platform, such as a slider. Simply grasp the large lever on the head and pull it up to release the clamp, then press it down to lock your head in place. Partially lifting the lever allows you to quickly and easily level the head.

When used with a separately available flowtech tripod, the aktiv8 enables you to spread the legs flat, getting as low to the ground as your head can without a tie-down knob getting in the way. You can also now mount your head directly onto a slider using a separately available aktiv system stud that screws onto support systems with a 3/8"-16 threaded stud.

The PrismBubble level system is pressed once to illuminate the bubble level to be illuminated or pressed twice to light up both the bubble level and the drag settings, a boon when working in darker environments. The bubble level also has a built-in prism, enabling you to more easily level the head when the legs are at set at maximum height or an awkward angle.

Mount your camera using the included Sideload Plate S that has both a 1/4-20 camera screw and a locating pin to prevent twisting. With a sliding range of 120 mm (4.7"), this head balances quickly to accommodate variously configured rigs The Sachtler aktiv8 head also features a detachable pan bar that can be mounted onto the rosettes on either the right or left side of the head.

Key Features:

SpeedLevel Technology

Use the large integrated lever to quickly mount, level, and lock the head on your tripod or other base; lift up to release, lift partially to level, and press down to lock the head firmly in place

SpeedSwap Base

Centred around a metal stud, the SpeedSwap base clamps onto any 75mm bowl tripod or to the separately available slider base; additional bases can be purchased separately to fit a second tripod, dolly, or slider

PrismBubble Level

The illuminated PrismBubble is visible from any height or angle, saving you time when levelling at higher or lower positions

12 kg Capacity Fluid Head

This 12 kg (26.5 lb) capacity fluid head is suited for larger DSLRs, mirrorless MFT cameras, and pro-style digital cine cameras

Stepped Counterbalance and Drag

15 steps of counterbalance and seven steps of pan and drag plus zero settings for free spins and tilts

Sideload Plate

The sideload plate has 120 mm (4.7") of travel for balancing your rig and both 1/4"-20 and 3/8"-16 camera screws

Sachtler Flowtech 75 MS Carbon Fibre Tripod with Mid-Level Spreader and Rubber Feet

The Sachtler Flowtech 75 MS Carbon Fibre Tripod with Mid-Level Spreader and Rubber Feet eschews the common single or double carbon fibre tube design and instead has redesigned the shape of the legs for improved torsional strength. The legs weigh just 2.9 kg (6.4 lb) yet they can support a payload of up to 20 kg (44 lb), and extend from a minimum height of 63 cm (24") to a maximum height of 157 cm (61") when using the included removable mid-level spreader. Each leg features a single clamping lever that locks and unlocks the sections.

Each leg extends or retracts independently from the other two, and when it is detached from the spreader each leg can pivot without affecting the other legs. This is especially useful when working on rough or uneven terrain. You can remove the spreader completely and lock each leg in one of three positions, so you can work without a spreader if you wish. This enables you to spread the legs extremely wide for low shots, while the tripod legs maintain their torsional stability. The dual spikes at the end of each leg provide extra grip when working on softer ground, and you can snap rubber feet onto the dual spikes for better grip when working on hard or delicate surfaces.

Key Features:

• Dual-stage, carbon fibre, 75mm bowl tripod
• Weighs only 2.9 kg (6.4 lb) but supports up to 20 kg (44 lb)
• The design and construction of the legs provide tremendous torsional stability. In other words, the legs resist twisting when you pan the tripod head.
• The included mid-level spreader allows you to work on uneven terrain such as stairs or rocks while preventing the legs from flying apart. When using the mid-level spreader, you can use the included rubber feet to protect delicate surfaces from the tripod's foot spikes.
• Each leg features a single clamping lever lock design at the top of the leg, near the 75mm bowl. This allows you to loosen all three leg sections from a single location, saving you time while reducing the wear and tear on your body as you don't have to bend down to loosen a leg lock at the bottom to lower or raise the legs.
• The legs incorporate a locking mechanism that enables the legs to move completely freely, suitable when working with a spreader, or to lock at one of three angles, suitable for use when working without a spreader.
• When closing the legs, there is room for the mid-level spreader to be folded up while remaining attached. The legs feature a magnetic locking system strong enough to hold them together during transport, but allows you to easily release the legs when you want to set them up.

Sachtler Padded Bag for flowtech 75 or TT Tripod with FSB Fluid Head

This Padded Bag from Sachtler is designed specifically for carrying a flowtech 75 or TT tripod equipped with an FSB fluid head. It is made with a high-density 900D fabric, which is both flame retardant and water-resistant to help ensure that your equipment stays safe. Additionally, layers of both open-cell and closed-cell foam are used in the construction to protect your gear against small bumps and shocks.

The bag opens via a full-length zipper found at the top, which allows for easy access while shooting. For transport, two straps on each side can be connected to an integrated handgrip for easy carrying. There are also small handles on each side of the bag where the zipper ends, and right next to them are D-rings that can be used to connect an optional shoulder strap. Finally, a clear plastic window on the outside allows you to insert a tag with your name or phone number for easy identification when travelling.

Key Features:

• Padded bag designed for carrying a flowtech 75 or TT tripod with an FSB fluid head
• 900D water-resistant fabric on the exterior, with layers of foam to help cushion gear against bumps
• Full-length zipper allows for easy access to the interior compartment
• Connecting hand straps, side handles, and D-rings available for transport
• Clear plastic window on one of the sides allows you to insert a name tag for easy identification