Direct Injection (D.I.) Boxes

• Balanced XLR Outputs
• Transformer Isolation
• Provides Ground Isolation
• Stereo/Mono Switch
• USB Powered

• For Multimedia Applications
• Mono 1/4", Stereo RCA, and 3.5mm Inputs
• Mono XLR Line-Level Input
• Mic-Level Mono Sum at XLR Out
• -15 dB Pad

• For Keyboards
• 2 x 1/4" Inputs with Thru Outputs
• -15 dB Pad for Active Instruments
• Handles Huge Transients without Chocking

• For Stage & Home Recording Studio Use
• Handles High-Output Instruments
• Transformer Isolated, No Ground Loops

• Passive re-amping device
• Allows for playing prerecorded tracks through amplifiers and pedals and re-record the results
• Level control for fine tuning the gain
• Ground lift switch, when activated helps to reduce hum and buzz caused by ground loops

• Unbalanced 1/4" Inputs.
• Balanced XLR Outputs.
• Passive Operation.
• Ground Lift.

• No Batteries Required
• Merge Switch Sums Stereo Instruments
• Low Cut/Polarity/Pad/Ground Switches

• Active Signal Patch
• Eliminates Hum and Buzz common to PCs
• 1/4" / RCA / 3.5mm Inputs for Any Source
• -15 dB Pad, Ground Lift Switch
• 48V Phantom Powered

• Equipped with Jensen Transformers
• -15 dB Pad Per Channel
• Flat Frequency Response
• Transformer-Isolated I/O
• 14-Gauge Steel Construction

• Connect a Computer to a PA or Mixer
• Built-In 24-Bit / 96 kHz Convertor
• 2 x Balanced XLR 3-Pin Outputs
• 3.5mm Stereo Headphone Output
• USB Type-B Input
• Operates on USB Bus Power

• Eliminates Hum & Buzz from Ground Loops
• Zero Phase & Harmonic Distortion
• Jensen Transformer Equipped

• Unbalanced 1/4" and XLR Inputs.
• Balanced XLR Output.
• Battery or Phantom Powered.

• Premium Performance.
• Rugged Design.
• Stackable Chassis with Durable Rubber Foot.
• Gold-plated Neutrik XLR Connector.

• Selectable Active/Passive Pickup Input.
• Z-Tone Variable Impedance.
• Switchable Pure/JFET Channel Tone.
• Switchable -20 dB Pad.
• 1/4" Thru and Main Outputs.

• Connects a Mobile Device to a PA/Mixer
• 3.5mm TRS Male Plug on 5' Attached Cable
• Switchable -15 dB Pad
• Custom-Wound Transformers
• 2 x 1/4" TRS Outputs
• Balanced XLR 3-Pin Output

• Increased Dynamic Range and Headroom
• 48V Phantom Powered & Switching Supply
• -15 dB Pad Switch

• Selectable Active/Passive Pickup Input.
• Z-Tone Variable Impedance.
• Switchable Pure/JFET Channel Tone.
• Buffers Signal for Long Cable Runs.
• Boost Circuit Adds Volume and Drive.

Passive DI Box. Instrument/Line in switch. Ground lift switch to eliminate hum.

• 4 Independent DI Channels
• Works as a 4-Channel Mixer
• Accepts Balanced and Unbalanced Signals

• Balancing and impedance matching
• Eliminates ground loop hum
• 4 independent DI boxes in a solid 19" housing (1U)
• Higher output level than a passive DI box
• THRU-output for passing the input signal
• Pure and unaltered low-noise audio

• Connecting devices with unbalanced or balanced outputs
• Eliminates ground loop hum
• Combo inputs
• 2 balanced XLR outputs per channel
• Ground-lift switch for each output
• Solid 19" housing, 1U

• Eliminates ground loop hum
• 4 independent DI boxes in a solid 19" housing (1U)
• THRU-output for passing the input signal
• Pure and unaltered low-noise audio
• Handles even high-level inputs
• Ground-lift switch for each output

• Passive splitter box
• One module has 4 channels

• Route a Stereo Instrument to Mic Inputs
• Converts Unbalanced to Balanced
• Converts High Impedance to Low Impedance
• Two 1/4" Unbalanced Inputs
• Two 1/4" TS Through Jacks

• Stereo Version of J48
• Low Distortion
• -15 dB Pad
• High-Pass Filter at 80 Hz
• Retains Instrument's Tone
• 14-Gauge Steel Construction

• Single Channel
• Battery or Phantom Powered
• Ground Lift
• Input Pad
• Rugged Enclosure

• Active.
• Polarity Switch.
• Ground Lift Switch.
• Rugged Construction.

• Dual Channel
• Passive
• 1/4" Mono, 1/8" Stereo and RCA Inputs
• Input Level Controls
• Ground Lift Switches

• Single space 8-channel rackmount microphone splitter
• Transformer isolated and direct outputs
• Channel pair link switches for doubling outputs or merging inputs
• Individual ground lift on each channel

• Route a Stereo USB Source to Mic Inputs
• Converts USB to Balanced Analogue
• USB 2.0 Type-B Input
• Two XLR 3-Pin Balanced Outputs
• 3.5mm Stereo Headphone Output

• Connect an Instrument to a Mic Input
• Converts Unbalanced to Balanced
• Converts High Impedance to Low Impedance
• 1/4" Unbalanced Input
• 1/4" Through Jack

• Connect an Instrument to a Mic Input
• Converts Unbalanced to Balanced
• Converts High Impedance to Low Impedance
• 1/4" Unbalanced Input
• 1/4" Through Jack

• Amp & Cab Simulator in Pedal Form
• Combo, Stack & 4x12 Cab Settings
• Presence Switch to Add Highs
• 180° Polarity Reverse Switch
• Ground Lift Switch